|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT LED TAPE AND REEL Pb Lead-Free Parts LHIR9553 DATA SHEET DOC. NO REV DATE : : QW0905-L HIR9553 A : 16 - Mar. - 2009 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHIR9553 Page 1/8 Package Dimensions 3.5 3.2 1.85 2.8 2.2 1.85 0.95 0.9 + 0.9 - Note : 1.All dimension are in millimeter tolerance is O 0.2mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0X -30X 30X -60X 60X 100% 75% 50% 25% 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHIR9553 Page 2/8 Absolute Maximum Ratings at Ta=25 J Ratings Parameter Symbol HIR Forward Current Peak Forward Current (300PPS,10g s Pulse) Power Dissipation Reverse Voltagev Operating Temperature Storage Temperature IF IFP PD Vr Topr Tstg 50 1 100 5 -55 ~ +100 -55 ~ +100 mA A mW V UNIT J J Electrical Optical Characteristics (Aa=25J ) PARAMETER Radiant Intensity Aperture Radiant Incidence Peak Emission Wavelength Spectral Line Half Width Forward Voltage Reverse Current Viewing Angle SYMBOL Le Ee Min. 1.1 0.15 Typ. 1.9 0.27 850 50 Max. UNIT mW/sr mW/cm nm nm 2 TEST CONDITION IF=20mA IF=20mA IF=20mA IF=20mA IF=20mA VR=5V f peak f VF IR 2c 1/2 1.2 1.6 100 120 V g A deg Note : 1.The forward voltage data did not including O 0.1V testing tolerance. 2. The radiant intensity data did not including O 15% testing tolerance. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHIR9553 2.Handling Precaution Page 3/8 1 Do not poke the silicone encapsulant with sharp objec t 2 Hold the LED only by the body 3 Do not atach assembied PCB 4 Do not touch the silicone encapsulant 5 Clean the silicone surface whit cotton bud with minimal pressure 6 Use pick and place nozzle per recommendation in datasheet LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHIR9553 Page 4/8 Typical Electro-Optical Characteristics Curve HIR CHIP Fig.1 Forward Current vs. Rorward Voltage 1000 Fig.2 Relative Radiant Power vs. Wavelength 1.0 100 10 1 0.1 0.0 Relative Radiant Power Normalize @20mA Forward Current[mA] 0.5 1.0 2.0 3.0 4.0 0.0 800 850 900 950 Forward Voltage[V] Wavelength[nm] Fig.3 Relative Radiant Power vs. Forward DC Current 10.0 Fig.4 Relative Radiant Power vs. Forward Peak Current 10.0 Relative Radiant Power Normalize @20mA 1.0 Relative Radiant Power Normalize @100 mA 1 10 100 1.0 0.1 0.1 10 100 1000 IFDC[mA] IFPK[mA] Fig.5 Forward DC Voltage vs. Temperature 1.2 Fig.6 Relative Radiant Power vs. Temperature 3.0 Forward DC Voltage Normalize @20mA, 25 J Relative Radiant Power Normalize @ 20mA, 25J 1.1 2.5 2.0 1.5 1.0 0.5 0.0 -40 1.0 0.9 0.8 -40 -20 0 20 40 60 80 100 -20 0 20 40 60 80 100 Ambient Temperature[J] Ambient Temperature[ J ] LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHIR9553 Recommended Soldering Conditions 1. Hand Solder Basic spec is O 280J 3 sec one time only. Page 5/8 2. Wave Solder Soldering heat Max. 260J 245O 5J within 5 sec 120 ~ 150J Preheat 120 ~ 180 sec 3. LEAD Reflow Solder Temp. (J ) 240 Rising +5J /sec Cooling -5J /sec 150 120 Preheat 60 ~ 120 sec 5sec Time 4. PB-Free Reflow Solder 1~5 C/sec 260 C MaX. 10sec.Max Preheat 180~200 C 1~5 C/sec Above 220 C 60 sec.Max. 120 sec.Max. Note: 1.Wave solder and reflow soldering should not be made more than one time. 2.You can just only select one of the soldering conditions as above. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHIR9553 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 J ~35J ,RH<60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 J ~ 35J ,RH<60%, they should be treated at 60JO 5 J fo r 15hrs. Page 6/8 Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHIR9553 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : O 30J ,RH<60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than168hrs in an atmosphere O 30J ,RH<60%, The single LED end product must use for 125 J for 10hours to eliminate wet 4.If opened more than168hrs in an atmosphere O 30J ,RH<60%, J The reel and carrier end product must use for 60 J for 24 hours to eliminate wet Page 7/8 Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. CAUTION LEVEL This bag contains MOISTURE-SENS DEVICES ITIVE 1.Shelf life in sealed bag:12months at O 30J and<60 (c) relative humidity(RH)eComplete package before open the packing f 2.Once the package is o pened,devices that will be subjected to infrared reflow must be (a)Mounted within 168 hours at factory conditions of30J/60MRH O (b)Stored at 30J/O10MRH within 168 hours O (c)The aluminum foil bag does out the vacuum ]d^From SMT to the IR timing control is 24 hours 12 3.If the humidity indicator 10 %RH is pink or af ter open package hrs house,the led monomer should be treated at125JO5Jfor10hrs. 4.The reel and carrier end product must use for 60 for 24 hours to J 5.eliminate wet I PC JED J- STD 033 / EC For the detail,please refer to the standard 3 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHIR9553 Reliability Test: Page 8/8 Classification Test Item Test Condition 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) Reference Standard MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 Operating Life Test High Temperature Storage Test Endurance Test Low Temperature Storage Test 1.Ta=105 JO 5J 2.t=1000 hrs (-24hrs, +72hrs) MIL-STD-883D:1008 JIS C 7021: B-10 1.Ta=-40 JO 5J 2.t=1000 hrs (-24hrs, +72hrs) JIS C 7021: B-12 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta=65JO 5J 3.RH=90 %~95 % 4.t=1000hrs O 2hrs 1.IR-Reflow In-Board,2 times 2.Ta=105 JO 5J & -40JO 5J (10min) (10min) 3.total 10 cycles MIL-STD-202F:103B JIS C 7021: B-11 Thermal Shock Test MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 Solder Resistance Test 1.T.Sol=260 JO 5J 2.Dwell Time= 10 O 1sec. 1.T.Sol=235 JO 5J 2.Immersion time 2 O 0.5sec 3.Immersion rate 25 O 2.5mm/sec 4.Immersion rate 25 O 2.5mm/sec 5.Coverage U 95% of the dipped surface 1.105J ~ 25J ~ 55J ~ 25J 30mins 5mins 30mins 5mins 2.10 Cyeles MIL-STD-202F: 210A MIL-STD-750D: 2031 JIS C 7021: A-1 MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 Solderability Test Environmental Test Temperature Cycling Solderability Test Ramp-up rate(183 J to Peak) +3 J second max Temp. maintain at 125( O 25)J 120 seconds max Temp. maintain above 183 J 60-150 seconds Peak temperature range 235 J +5-0J Time within 5 J of actual Peak Temperature(tp) 10-30 seconds Ramp-down rate +6 J /second max MIL-STD-750D:2031.2 J-STD-020 |
Price & Availability of LHIR9553 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |